Sunday, 23 March 2014

Wood Anemone in flower

Spring is well and truly here - there are Wood Anemones in flower!

Wood Anemone flowers 2014-03-22 16.02.40

The woodland as a whole is looking much greener than it was just a week or two ago. This picture is over in Alex's wood, where I was helping my friend Rich (the woodland manager) finish off the last of the road edge trees.
Wood Anemone flowers 2014-03-22 16.03.35

Rich has been busy experimenting with a new way of stacking logs, using lengths at right-angles to make air gaps between the logs. He's going to see if this speeds up the seasoning of the wood, but it also had the advantage of removing the need for stakes at the ends of the stack:
Stacked logs 2014-03-22 15.27.25

Stacked logs 2014-03-22 15.27.32


Click here to read the rest of this post.

Saturday, 8 March 2014

Hedges: laying, layering and pleaching

I've been out enjoying the sunshine, helping my friend Rich with some work in a bit of woodland near ours, cutting roadside trees and recreating a hedge there. We also had the help of Tom for a bit, another friend of mine. Here's the work site:

DSC_8149 roadside tree cutting

The tree cutting was all pretty straightforward, with the main challenge being the phone line the trees had grown round. But use of a long pole with saw or loppers on the end made it pretty easy.

Rich showed us how to 'layer' a tree to fill in gaps in the hedge. This starts with a stem, which is cut most of the way through, making sure to leave both some bark and some sap wood - this allows the rest of the stem to stay alive. Rich used an axe to cut through the stem, though for a larger stem you could start with a chainsaw. This bit of the process is known as 'pleaching', and the cut stem is sometimes called a pleacher.
DSC_8151 Pleached tree for layering in a hedge

The idea is to cut it thin enough that the stem can be bent over to touch the ground. The bark needs to be scraped off the underside of the bit that will touch the ground:
DSC_8153 layering a tree

You then scrape out a small hole, and put the pleached stem into it:
DSC_8156 layering a tree

The stem is held in the ground by a wooden peg - in this case made from part of a forked stem:
DSC_8158 layering a tree

This is banged into the ground with whatever tool is nearest - an axe in this case:
DSC_8162 layering a tree

This leaves the pleached stem securely fixed in the ground - where the bark was scraped off new roots will grow.
DSC_8164 layering a tree

Finally you just cover it back over with some earth and leaves, and leave it to get on with it. As well as roots growing out of the scraped sections, shoots will also grow out of the side of the stem, as with a cut coppice stool. The idea is that after a period of time the bit of wood joining the pleached stem to the original tree dies off, leaving you a new independent tree (a clone of the original one).
DSC_8167 layering a tree

We also pleached some stems that weren't fixed into the ground - this is 'laying' a hedge, meaning that the stems are laid over on their sides. Again, new shoots will grow vertically from the stem, but in this case enough wood is left attaching it to the main tree that it will continue to be fed by it permanently:
DSC_8168 Pleached tree for hedge laying

DSC_8170 Pleached tree for hedge laying

Here's the section cut so far - there's about the same amount again still to do:
DSC_8171 roadside tree cutting


Click here to read the rest of this post.

Saturday, 1 March 2014

Ducks in the woods and a new shelter roof

See, I told you the woods were flooded... we have Mallards swimming around now...

Mallards in the woods! IMG_20140301_144708

Here's a pic of the River Rother from a couple of weeks ago, which gives you an idea of how waterlogged the area around Rye is!
River Rother in flood, Feb 2014

At least one good sign though - bluebell shoots!
Bluebell shoots appearing! DSC_7983

The wet and windy winter had also accelerated the decay of parts of our shelter roof in the woods, so we spent some time over the last couple of weekends getting it sorted...

First we fixed some wooden beams across the existing roof:


Then wedged a few bits of wood underneath to stiffen them up - the roof bows a bit, hence the gap in the middle.

To go on top of them we had some sterling board (OSB - Oriented Strand Board), which we'd treated with a preservative, and corrugated panels to go on top of them:

And of course the solar PV to recharge the drill...

Once the sterling boards were on top, it was pretty easy to move around and screw them down:

Then the corrugated panels and the ridge pieces went on top:

They were supplied with some special caps and nails, but we opted to use screws instead of nails. The screw went through the cap:

Was then tightened until it was holding the panel firmly:

Then finally you flip the centre of the cap over and press it down to create a watertight seal:

We spent a good chunk of one day making half of the roof:

Then came back the following weekend with more power tools and got the second half done much quicker!
Woodland shelter DSC_7986

We went today as well to do some track repair, but no pics of that - not much to see, just mud!


Click here to read the rest of this post.